CognitiveTPG A798 Instruction Manual Page 90
- Page / 121
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4: Programming Commands90
Revision C 12/09
A798-PG00001C
Page mode
Page mode is one of two modes that the A798 printer uses to operate. Standard mode is typical of how most printers
operate by printing data as it is received and feeding paper as the various paper feed commands are received. Page mode is
different in that it processes or prepares the data as a “page” in memory before it prints it. Think of this as a virtual page.
The page can be any area within certain parameters that you dene. The page is printed using either the FF (0C) or the
ESC FF (1B 0C) command.
The select page mode command (1B 4C) puts the printer into page mode. Any commands that are received are interpreted
as page mode commands. Several commands react differently when in standard mode and page mode. The descriptions of
these individual commands in this chapter indicate the differences in how they operate in the two modes.
These commands describe the operation for 80mm paper. If the printer supports 82.5mm paper, the dot spacing is the same
but there are 640 printable dots rather than 576 printable dots on 80mm paper.
Print and return to standard mode
ASCII FF
Hexadecimal 0C
Decimal 12
When printing is completed, values for select print direction in page mode (1B 54n) and set print area in page mode (1B
57 n1, n2, …n8) and the position for buffering character data are set. Buffered data is not deleted from the printer.
The processed data is printed and the printer returns to standard mode. The developed data is deleted after being printed.
For more information see page mode in this document.
Exceptions
This command is enabled only in page mode.
Cancel print data in page mode
ASCII CAN
Hexadecimal 18
Decimal 24
Deletes all the data to be printed in the “page” area. Any data from the previously selected “page” area that is also part of
the current data to be printed is deleted.
Exceptions
This command is only used in page mode.
Print data in page mode
ASCII ESC FF
Hexadecimal 1B 0C
Decimal 27 12
Collectively prints all buffered data in the printing area.
After printing, the printer does not clear the buffered data and sets values for select print direction in page mode (1B 54 n)
and set print area in page mode (1B 57 …), and sets the position for buffering character data.
Exceptions
This command is enabled only in page mode.
- Programming Guide 1
- Contents 3
- 4 Revision C 12/09 4
- 6 Revision C 12/09 6
- 8 Revision C 12/09 8
- A798 Programming Guide 10
- Chapter 1: About this Guide 10
- Revision C 12/09 10
- A798-PG00001C 10
- Start-up Diagnostics 11
- Runtime diagnostics 12
- Remote diagnostics 12
- Comm Class” 13
- Indicators 14
- Printer conguration 15
- Conguring the printer 16
- Communication interface 17
- Diagnostic modes 18
- Printer emulations 19
- Overview of commands 23
- Comparison to A793 23
- Character appearance 25
- Print zones 25
- Rotated printing commands 26
- Emulation modes 27
- Commands listed by function 29
- Text characteristics 30
- Graphics 31
- Bar codes 32
- Page mode 32
- User data storage 32
- Command conventions 33
- Command descriptions 34
- Generate tone 35
- Initialize printer 35
- Select cut mode and cut paper 38
- Print test form 38
- Print and paper feed 39
- Add n extra dot rows 40
- Print and feed paper 41
- Print and feed n lines 41
- Horizontal tab 42
- Set column 42
- Set vertical line spacing 44
- Set horizontal tab positions 44
- Set relative print position 45
- To move to the left: 45
- Select justication 46
- Set left margin 46
- Set printing area width 47
- Text characteristics commands 48
- Select pitch (column width) 49
- Select print mode 50
- 51
- Cancel user-dened character 53
- Select or cancel italic print 54
- Select character size 57
- Select bit image mode 60
- Print Flash Logo 62
- Dene Flash Logos 62
- Select the current logo 62
- Dene downloaded bit image 63
- Print downloaded bit image 64
- Print raster graphics 65
- Status command introduction 65
- Batch mode 65
- Transmit paper sensor status 67
- Transmit printer ID 68
- Transmit status 71
- Send printer software version 72
- Real time commands 73
- Moving data through the buer 74
- Real time status transmission 74
- Real time request to printer 77
- Real time commands disabled 78
- Unsolicited status mode 79
- Print bar code 84
- Print multiple barcodes 85
- 29 107 n d1... 00 87
- 29 107 m nL nH d1... dn 87
- Select PDF 417 parameters 88
- Select bar code width 89
- Sample symbol description: 89
- Select page mode 91
- Select standard mode 92
- Set print area in page mode 93
- Execute macro 95
- Erase user ash sector 99
- Flash download 100
- Get rmware CRC 101
- Return microprocessor CRC 101
- Erase selected ash sector 102
- Reset rmware 102
- Return main program ash CRC 102
- Appendix A: 104
- Appendix B: 108
- Resident Character Sets 108
- Code page 737 (Greek) 109
- Code page 850 (Multilingual) 110
- Code page 852 (Slavic) 111
- Code page 857 (Turkish) 112
- Code page 860 (Portuguese) 114
- Code page 862 (Hebrew) 115
- Code page 865 (Nordic) 117
- Code page 866 (Cyrillic) 118
Related products and manuals for Print & Scan CognitiveTPG A798
(36 pages)© 2020, manymanuals.com. All rights reserved. | 0.677 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals