CognitiveTPG A798 Instruction Manual Page 36
- Page / 121
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4: Programming Commands36
Revision C 12/09
A798-PG00001C
Select paper sensors to output paper-end signals
ASCII ESC c 3 n
Hexadecimal 1B 63 33 n
Decimal 27 99 51 n
Value of n:
If either bit 0 or bit 1 is on, the paper roll near-end sensor is selected as the paper sensor outputting paper-end signals.
If either bit 2 or bit 3 is on, the paper roll-end sensor is selected as the paper sensor outputting paper-end signals.
Bit Position Hex Decimal Function
0 O 00 0 Paper roll near-end sensor disabled
On 01 1 Paper roll near-end sensor enabled
1 O 00 0 Paper roll near-end sensor disabled
On 02 2 Paper roll near-end sensor enabled
2 O 00 0 Paper roll-end sensor disabled
On 04 4 Paper roll-end sensor enabled
3 O 00 0 Paper roll-end sensor disabled
On 08 8 Paper roll-end sensor enabled
4, 5, 6, 7 – – – Undened
Range of n: 1–255
Default of n: 12
Species the paper sensor to output a paper-end signal. Multiple sensors may be selected to signal when paper has run out.
When multiple sensors have been selected, anytime one of the sensors detects a paper-end, the paper end signal is output.
When this command is executed a sensor is switched. The paper-end signal switching is delayed depending on the receive
buffer state.
Exceptions
The command is ignored, except in parallel communications.
Select sensors to stop printing
ASCII ESC c 4 n
Hexadecimal 1B 63 34 n
Decimal 27 99 52 n
Value of n: Sensor status
Sensor Status
Bit Sensor 0 1
0 Receipt paper near-end Disabled Enabled
1 Receipt paper near-end Disabled Enabled
2–4 Undened
6 Undened
Bits 5 and 7 are not used.
Default: 0
Determines which sensor stops printing on the respective station. The command does not affect the paper out status on the
receipt station, which will automatically stop the printer when the paper is depleted.
- Programming Guide 1
- Contents 3
- 4 Revision C 12/09 4
- 6 Revision C 12/09 6
- 8 Revision C 12/09 8
- A798 Programming Guide 10
- Chapter 1: About this Guide 10
- Revision C 12/09 10
- A798-PG00001C 10
- Start-up Diagnostics 11
- Runtime diagnostics 12
- Remote diagnostics 12
- Comm Class” 13
- Indicators 14
- Printer conguration 15
- Conguring the printer 16
- Communication interface 17
- Diagnostic modes 18
- Printer emulations 19
- Overview of commands 23
- Comparison to A793 23
- Character appearance 25
- Print zones 25
- Rotated printing commands 26
- Emulation modes 27
- Commands listed by function 29
- Text characteristics 30
- Graphics 31
- Bar codes 32
- Page mode 32
- User data storage 32
- Command conventions 33
- Command descriptions 34
- Generate tone 35
- Initialize printer 35
- Select cut mode and cut paper 38
- Print test form 38
- Print and paper feed 39
- Add n extra dot rows 40
- Print and feed paper 41
- Print and feed n lines 41
- Horizontal tab 42
- Set column 42
- Set vertical line spacing 44
- Set horizontal tab positions 44
- Set relative print position 45
- To move to the left: 45
- Select justication 46
- Set left margin 46
- Set printing area width 47
- Text characteristics commands 48
- Select pitch (column width) 49
- Select print mode 50
- 51
- Cancel user-dened character 53
- Select or cancel italic print 54
- Select character size 57
- Select bit image mode 60
- Print Flash Logo 62
- Dene Flash Logos 62
- Select the current logo 62
- Dene downloaded bit image 63
- Print downloaded bit image 64
- Print raster graphics 65
- Status command introduction 65
- Batch mode 65
- Transmit paper sensor status 67
- Transmit printer ID 68
- Transmit status 71
- Send printer software version 72
- Real time commands 73
- Moving data through the buer 74
- Real time status transmission 74
- Real time request to printer 77
- Real time commands disabled 78
- Unsolicited status mode 79
- Print bar code 84
- Print multiple barcodes 85
- 29 107 n d1... 00 87
- 29 107 m nL nH d1... dn 87
- Select PDF 417 parameters 88
- Select bar code width 89
- Sample symbol description: 89
- Select page mode 91
- Select standard mode 92
- Set print area in page mode 93
- Execute macro 95
- Erase user ash sector 99
- Flash download 100
- Get rmware CRC 101
- Return microprocessor CRC 101
- Erase selected ash sector 102
- Reset rmware 102
- Return main program ash CRC 102
- Appendix A: 104
- Appendix B: 108
- Resident Character Sets 108
- Code page 737 (Greek) 109
- Code page 850 (Multilingual) 110
- Code page 852 (Slavic) 111
- Code page 857 (Turkish) 112
- Code page 860 (Portuguese) 114
- Code page 862 (Hebrew) 115
- Code page 865 (Nordic) 117
- Code page 866 (Cyrillic) 118
Related products and manuals for Print & Scan CognitiveTPG A798
(36 pages)© 2020, manymanuals.com. All rights reserved. | 1.602 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals