CognitiveTPG A798 Instruction Manual Page 101
- Page / 121
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4: Programming Commands 101
Revision C 12/09
A798-PG00001C
Return segment number status of ash memory
ASCII GS SOH
Hexadecimal 1D 01
Decimal 29 1
Returns the size of the ash used. There may be 16 (1 Meg) or 32 (2 Meg) sectors in ash memory. This command assures
that the rmware to be downloaded is the appropriate size for ash memory. The value returned is the maximum sector
number that can be accepted by the select sector to download (1D 02 nn) command.
Exceptions
Available only in download mode.
Select ash memory sector to download
ASCII GS STX nn
Hexadecimal 1D 02 nn
Decimal 29 2 nn
Value of n: The ash sector to which the next download operation applies
Range of n: 0
Selects the ash sector (nn) for which the next download operation applies. The values of the possible sector are restricted,
depending upon the ash part type. The printer transmits an ACK if the sector number is acceptable or an NAK if the
sector number is not acceptable. Sector numbers start at 0.
Exceptions
Available only in download mode.
Get rmware CRC
ASCII GS ACK
Hexadecimal 1D 06
Decimal 29 6
Causes the printer to calculate the CRC for the currently selected sector and transmits the result. This is performed
normally after downloading a sector to verify that the downloaded rmware is correct. The printer also calculates the CRC
for each sector during power up and halts the program if any sector is erroneous.
The printer transmits ACK if the calculated CRC is correct for the selected sector; NAK if the CRC is incorrect or if no
sector is selected.
Return microprocessor CRC
ASCII GS BEL
Hexadecimal 1D 07
Decimal 29 7
Returns the CRC calculated over the boot sector code space.
Formulas
ACK <low byte> <high byte>
Erase all ash contents except boot sector
ASCII GS SO
Hexadecimal 1D 0E
Decimal 29 14
Causes the entire ash memory to be erased.
The printer returns ACK if the command is successful; NAK if it is unsuccessful.
Exceptions
Available only in download mode.
- Programming Guide 1
- Contents 3
- 4 Revision C 12/09 4
- 6 Revision C 12/09 6
- 8 Revision C 12/09 8
- A798 Programming Guide 10
- Chapter 1: About this Guide 10
- Revision C 12/09 10
- A798-PG00001C 10
- Start-up Diagnostics 11
- Runtime diagnostics 12
- Remote diagnostics 12
- Comm Class” 13
- Indicators 14
- Printer conguration 15
- Conguring the printer 16
- Communication interface 17
- Diagnostic modes 18
- Printer emulations 19
- Overview of commands 23
- Comparison to A793 23
- Character appearance 25
- Print zones 25
- Rotated printing commands 26
- Emulation modes 27
- Commands listed by function 29
- Text characteristics 30
- Graphics 31
- Bar codes 32
- Page mode 32
- User data storage 32
- Command conventions 33
- Command descriptions 34
- Generate tone 35
- Initialize printer 35
- Select cut mode and cut paper 38
- Print test form 38
- Print and paper feed 39
- Add n extra dot rows 40
- Print and feed paper 41
- Print and feed n lines 41
- Horizontal tab 42
- Set column 42
- Set vertical line spacing 44
- Set horizontal tab positions 44
- Set relative print position 45
- To move to the left: 45
- Select justication 46
- Set left margin 46
- Set printing area width 47
- Text characteristics commands 48
- Select pitch (column width) 49
- Select print mode 50
- 51
- Cancel user-dened character 53
- Select or cancel italic print 54
- Select character size 57
- Select bit image mode 60
- Print Flash Logo 62
- Dene Flash Logos 62
- Select the current logo 62
- Dene downloaded bit image 63
- Print downloaded bit image 64
- Print raster graphics 65
- Status command introduction 65
- Batch mode 65
- Transmit paper sensor status 67
- Transmit printer ID 68
- Transmit status 71
- Send printer software version 72
- Real time commands 73
- Moving data through the buer 74
- Real time status transmission 74
- Real time request to printer 77
- Real time commands disabled 78
- Unsolicited status mode 79
- Print bar code 84
- Print multiple barcodes 85
- 29 107 n d1... 00 87
- 29 107 m nL nH d1... dn 87
- Select PDF 417 parameters 88
- Select bar code width 89
- Sample symbol description: 89
- Select page mode 91
- Select standard mode 92
- Set print area in page mode 93
- Execute macro 95
- Erase user ash sector 99
- Flash download 100
- Get rmware CRC 101
- Return microprocessor CRC 101
- Erase selected ash sector 102
- Reset rmware 102
- Return main program ash CRC 102
- Appendix A: 104
- Appendix B: 108
- Resident Character Sets 108
- Code page 737 (Greek) 109
- Code page 850 (Multilingual) 110
- Code page 852 (Slavic) 111
- Code page 857 (Turkish) 112
- Code page 860 (Portuguese) 114
- Code page 862 (Hebrew) 115
- Code page 865 (Nordic) 117
- Code page 866 (Cyrillic) 118
Related products and manuals for Print & Scan CognitiveTPG A798
(36 pages)© 2020, manymanuals.com. All rights reserved. | 1.251 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals