CognitiveTPG A798 Instruction Manual Page 56
- Page / 121
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4: Programming Commands56
Revision C 12/09
A798-PG00001C
Select international character set
ASCII: ESC t n
Hexadecimal: 1B 74 n
Decimal: 27 116 n
Value of n:
A798 native mode A793 emulation Application Compatible Escape Command
emulation (1B 52 n only)
0 = Code Page 437 0 = Code Page 437 0 = U.S.A.
1 = Code Page 850 Not 0 = Code Page 850 1 = France
2 = Code Page 852 2 = Germany
3 = Code Page 860 3 =-U.K.
4 = Code Page 863 4 = Denmark I
5 = Code Page 865 5 = Sweden
6 = Code Page 858 6 = Italy
7 = Code Page 866 7 = Spain
8 = Code Page 1252 8 = Japan
9 = Code Page 862 9 = Norway
10 = Code Page 737, Greek (in A798 native mode and A794 emulation)
12 = Code 857
Default: 0 (Code Page 437)
Selects the character set to be used. Look in “Appendix B: Resident Character Sets” in the A798 User Guide Programming
Supplement for the character sets.
There are two codes for this command (See “Select international character code, 1B 52 n.) Both codes perform the same
function.
Related information
The LEGACY emulation selection applies only to the command “Select international character code” (1B 52 n).
The LEGACY emulation generates the same as A798 native mode for the command “Select international character set”
(1B 74 n).
Select or cancel upside-down print mode
ASCII ESC { n
Hexadecimal 1B 7B n
Decimal 27 123 n
Value of n: 0 = Cancel
1 = Set
Default: 0 (Cancel)
Prints upside-down characters. The command may be combined with clockwise rotated print (1B 56) or counter-clockwise
rotated print (1B 12). The character order is inverted in the buffer so text is readable. Only bit 0 is used. Bits 1-7 are not
used. See summary of rotated printing in this document for more information.
Exceptions
The command is valid only at the beginning of a line.
It cannot be used with right side up characters on the same line.
- Programming Guide 1
- Contents 3
- 4 Revision C 12/09 4
- 6 Revision C 12/09 6
- 8 Revision C 12/09 8
- A798 Programming Guide 10
- Chapter 1: About this Guide 10
- Revision C 12/09 10
- A798-PG00001C 10
- Start-up Diagnostics 11
- Runtime diagnostics 12
- Remote diagnostics 12
- Comm Class” 13
- Indicators 14
- Printer conguration 15
- Conguring the printer 16
- Communication interface 17
- Diagnostic modes 18
- Printer emulations 19
- Overview of commands 23
- Comparison to A793 23
- Character appearance 25
- Print zones 25
- Rotated printing commands 26
- Emulation modes 27
- Commands listed by function 29
- Text characteristics 30
- Graphics 31
- Bar codes 32
- Page mode 32
- User data storage 32
- Command conventions 33
- Command descriptions 34
- Generate tone 35
- Initialize printer 35
- Select cut mode and cut paper 38
- Print test form 38
- Print and paper feed 39
- Add n extra dot rows 40
- Print and feed paper 41
- Print and feed n lines 41
- Horizontal tab 42
- Set column 42
- Set vertical line spacing 44
- Set horizontal tab positions 44
- Set relative print position 45
- To move to the left: 45
- Select justication 46
- Set left margin 46
- Set printing area width 47
- Text characteristics commands 48
- Select pitch (column width) 49
- Select print mode 50
- 51
- Cancel user-dened character 53
- Select or cancel italic print 54
- Select character size 57
- Select bit image mode 60
- Print Flash Logo 62
- Dene Flash Logos 62
- Select the current logo 62
- Dene downloaded bit image 63
- Print downloaded bit image 64
- Print raster graphics 65
- Status command introduction 65
- Batch mode 65
- Transmit paper sensor status 67
- Transmit printer ID 68
- Transmit status 71
- Send printer software version 72
- Real time commands 73
- Moving data through the buer 74
- Real time status transmission 74
- Real time request to printer 77
- Real time commands disabled 78
- Unsolicited status mode 79
- Print bar code 84
- Print multiple barcodes 85
- 29 107 n d1... 00 87
- 29 107 m nL nH d1... dn 87
- Select PDF 417 parameters 88
- Select bar code width 89
- Sample symbol description: 89
- Select page mode 91
- Select standard mode 92
- Set print area in page mode 93
- Execute macro 95
- Erase user ash sector 99
- Flash download 100
- Get rmware CRC 101
- Return microprocessor CRC 101
- Erase selected ash sector 102
- Reset rmware 102
- Return main program ash CRC 102
- Appendix A: 104
- Appendix B: 108
- Resident Character Sets 108
- Code page 737 (Greek) 109
- Code page 850 (Multilingual) 110
- Code page 852 (Slavic) 111
- Code page 857 (Turkish) 112
- Code page 860 (Portuguese) 114
- Code page 862 (Hebrew) 115
- Code page 865 (Nordic) 117
- Code page 866 (Cyrillic) 118
Related products and manuals for Print & Scan CognitiveTPG A798
(36 pages)© 2020, manymanuals.com. All rights reserved. | 0.137 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals